A five-element model is presented based on the test results.
利用三軸流變試驗儀,模擬基坑開挖時坑底土體的應力路徑,進行卸載流變試驗,并提出一個五元件模型對試驗結果進行模擬。
Based on the present study situation, the rheological constitutive models of rock and soil are sorted into four kinds: component model, yield sw-face model, endochronic plasticity model and experiential model.
基于巖土流變模型的研究現狀，把各種流變模型分成４類：元件模型、屈服面模型、內時模型和經驗?zāi)Ｐ汀?/p>
By use of standard coefficient method and distance method,a method to quantitatively assess the simulation accuracy of component models is proposed.
結合規范系數法與距離法提出了一種定量判斷元件模型仿真準確度的方法。
Based on experimentresearch and model conversion of model device on its 30 incline axial flow pump,it foundthat the comprehensive characteristic curves of model device and reality device,it will beimportant to the design of Xing-Xiagang and other same type pump stations.
采用三維邊界無法數值模擬了新夏港泵站的進水流道，并通過對該30°斜軸泵模型裝置的試驗研究和模型換算，得出了模型及原型裝置的綜合特性曲線，該成果可作為新夏港和其它相同類型泵站設計的重要依
Based on similitude theory and hydrodynamics,the device model of tubular pumping station in Huangmayong is set up.
按照流體力學相似原理建立了黃麻涌雙向豎井貫流泵站流道的裝置模型,試驗測定了模型泵裝置在指定葉片角度下運行的裝置綜合特性曲線,將泵裝置綜合特性曲線換算成原型泵的特性曲線,同時試驗測定在不同工況運行狀態下的汽蝕性能,并觀察進出水流道的流態,得到了汽蝕性能結果,提出了建設泵站的注意事項和相應的改進措施。
In order to make the Jiangdu fourth pumping station run stably and safely,three high frequency vibration accelerometers were adapted to measure the vibration characteristics of the device model,and the measurement results were analyzed using RMS of vibration acceleration.
為了確保江都四站軸流泵機組的安全穩定運行,采用三個高頻振動加速度傳感器對裝置模型不同工況下的振動信號進行了采集,并運用加速度有效值對測量結果進行了分析。
Application method of RTDS user define component model (UDC)
RTDS用戶自定義元件模型(UDC)的應用方法
Derivation of the theory and relational expression of three elements model, and its application to textile.
介紹了三元件模型理論及其本構關系式的推導,以及三元件模型理論在紡織上的應用。
Element Modeling and System Simulation for Power System Harmonics;
電力系統諧波分析的元件模型和系統仿真
Analysis of Radio-Frequency Device Model and the Design of Low Noise Amplifier;
射頻元件模型分析與低噪聲放大器設計
Study on MDA Software Modeling Technology Based on Meta Model
基于元模型的MDA軟件建模技術研究
Adds a grouping of model elements to your Component diagram.
將一組模型元素添加到組件圖中。
Research on Credit Management Architecture Based on Meta-Model;
基于元模型的信貸管理軟件構架研究
The Finite Element Modeling and Simulation for Thermomechanical Analysis of PCBA;
PCB組件熱—力分析的有限元模型及仿真
Research on Design and Application of Dual-Hall Element Combined Models
雙霍爾元件組合模型設計與應用研究
Reserch on Printed Circuit Board Electronic Components Dismantling Model and Experiments
電路板電子元件拆除模型與實驗研究
Study on Model and Conformability of SPC System Document for Electronic Components
電子元器件SPC體系文件模型及符合性探討
The establishment of 3D-FE model libraries for the elements of the RPD
可摘局部義齒各部件三維有限元模型庫的建立
Visual Linearized Model of Power System Containing FACTS and Its Application;
含F(xiàn)ACTS元件電力系統直觀線性化模型及應用研究
The Numerical Optimization of the Stators in Centrifugal Compressor Model Stage with Small Flow Coefficient;
離心壓縮機小流量模型級靜止元件的數值優化
The Studies of Cellular Automata Models of Traffic Flow with Open Boundary Conditions;
開放邊界條件下元胞自動機交通流模型的研究
Finite Element Solution of Coupled Rotor-Bearing System & Software Development;
轉子—軸承耦合系統有限元求解模型與軟件開發
The Polynomial Model of Circuit and Its Application in Component Matching;
電路的多項式模型及其在元件匹配中的應用
Study on the Dynamic City Model Based on Cellular Automata and Population Condition;
人口條件約束下的城市元胞自動機模型研究