The effects of cooling rate on Ms and microstructures of Fv520(B) steel have been studied by hot expansion method,micro scopic test and XRD.
利用膨脹法、金相、XRD法研究了冷卻速度對Fv520(B)鋼Ms點及其組織的影響。
It shows that with the increase of compression deformation of parent phase, Ms point (starting temperature of martensitic transformation) of {259}f martensitic transformation is rising.
試驗結果表明,母相壓縮變形使{259}f馬氏體轉變的Ms點(馬氏體開始形成溫度)升高,變形量較小時Ms點升高較快,變形量較大時Ms點升高的趨勢不如變形量較小時明顯;變形量較小時{259}f馬氏體沒有擇優取向,母相壓縮變形量為30%時的馬氏體和對應的表面浮凸沿滑移線方向分別以細片狀和細條狀平行排列成“簇”;變形量較小時{259}f馬氏體片的邊界與未變形相比更平直,30%母相壓縮變形得到的馬氏體片邊緣較破碎,而經50%母相壓縮變形后,不但馬氏體片的邊緣較破碎,而且中脊也開始彎曲或折斷,在浮凸表面上表現為小的溝痕。
The effects of rare earth on TTT curve,Ms point and phase transformation critical points of 30CrMnSi cast steel were investigated.
研究了稀土對 30 Cr Mn Si鑄鋼 TTT曲線及相變點的影響 ,其結果為開始轉變曲線右移 ,終了轉變曲線左移 ,相變臨界點滯后 ,Ms點升
The Ms points and morphology of the crystalline structure for the Fe-30.
96Ti鐵基合金的Ms點、馬氏體形貌及合金的晶體結構進行了分析研究。
The influence of cooling rate on MS temperature of CuZnAlMnNi shape memory alloy was investigated by differential scanning calorimetry.
用差示掃描量熱分析技術研究了冷卻速率對CuZnAlMnNi記憶合金Ms點的影響。
Finally we target on cost to establish a integer programming model based on the limitations of purchasing needs of spectators and commercial benefits,and use a set of reasonable data to compute the concrete design scheme of the MS site by simulation of Matlab.
最后,建立了以成本為目標函數,以觀眾的購物欲望、商業贏利為約束條件的整數規劃模型,對其中的參數N、n、Q、q、λ進行合理估計,給出一組數據,借助MATLAB軟件計算出了MS網點的最佳設計方案。